No Widgets found in the Sidebar

Securitron exit button wiring diagram

If you’re installing an exit button for a security system, it’s important to understand how to properly wire it. The exit button is a crucial component of any access control system, allowing individuals inside a building to easily exit in case of an emergency or when simply leaving. In this article, we will discuss the wiring diagram for a Securitron exit button.

Securitron is a well-known manufacturer of access control products, including exit buttons. Their exit buttons are designed to provide a secure and reliable way for people to exit a building, while also integrating seamlessly with other components of an access control system.

The wiring diagram for a Securitron exit button typically includes connections for power, ground, and the NO (normally open) or NC (normally closed) contacts. It is important to follow the manufacturer’s instructions and reference the appropriate wiring diagram to ensure proper installation.

Securitron Exit Button Wiring Diagram

Securitron Exit Button Wiring Diagram

If you are looking for information on how to wire a Securitron exit button, you have come to the right place. This wiring diagram will show you the necessary steps to properly install and connect your exit button to the Securitron access control system.

Components:

  • Securitron exit button
  • Power supply
  • Electromagnetic lock
  • Wires

Step-by-step instructions:

  1. Start by connecting the power supply to the Securitron exit button. Make sure to follow the manufacturer’s instructions and use the correct voltage.
  2. Next, connect the exit button to the electromagnetic lock. The exit button is typically wired in a normally open configuration, meaning the circuit is open when the button is not pressed. When the button is pressed, it closes the circuit and releases the lock. Consult the wiring diagram provided by Securitron for the specific wiring configuration.
  3. Once the exit button is connected to the lock, connect the power supply to the electromagnetic lock. Again, make sure to use the correct voltage and follow the manufacturer’s instructions.
  4. Finally, connect the power supply to the access control system. This will allow the system to control the lock and provide access to authorized individuals.
  5. Test the system to ensure everything is functioning properly. Press the exit button and verify that the lock releases.

This wiring diagram is a general guide and may vary depending on the specific model of Securitron exit button and access control system you are using. Always refer to the manufacturer’s instructions and consult a professional if you are unsure about any aspect of the installation process.

Exit Button Connection Electromagnetic Lock Connection
Exit Button Electromagnetic Lock
Power Supply Positive (+) Power Supply Positive (+)
Power Supply Negative (-) Power Supply Negative (-)
Exit Button Signal/Control Wire Lock Signal/Control Wire

Understanding the Basics of Securitron Exit Button Wiring

Understanding the Basics of Securitron Exit Button Wiring

Securitron exit buttons are an essential component of access control systems, providing a means for individuals to exit a secured area. Proper wiring of these exit buttons is crucial to ensure their functionality and integration with the overall access control system.

Power Supply: The first step in wiring a Securitron exit button is to connect it to a power supply. The exit button typically requires a low-voltage power source, such as 12 or 24 volts DC. This power supply can be provided by a dedicated power supply unit or obtained from the main access control system.

Switch Wiring: The next step is to connect the switch terminals of the exit button to the control panel or access control device. The exit button usually has two terminals that must be connected to the input terminals of the control panel. These terminals are usually labeled as “COM” for the common terminal and “NO” for the normally open terminal. The common terminal is typically connected to the ground or negative side of the power supply, while the normally open terminal is connected to the input terminal of the control panel.

Indicator Wiring: In addition to the switch wiring, Securitron exit buttons often feature built-in indicators, such as LED lights, to provide visual feedback. These indicators are wired in parallel with the switch terminals and are typically connected to the power supply and ground. The exact wiring configuration may vary depending on the specific exit button model, so it is important to refer to the manufacturer’s documentation for the correct wiring diagram.

Final Connections: Once the switch and indicator wiring is completed, the final step is to connect the control panel or access control device to the locking device, such as an electromagnetic lock or electric strike. This typically involves connecting the output terminals of the control panel to the appropriate input terminals of the locking device, ensuring that the correct polarity is maintained.

In summary, understanding the basics of Securitron exit button wiring involves connecting the exit button to a power supply, wiring the switch terminals to the control panel, wiring the indicator (if applicable), and making the final connections to the locking device. Following the manufacturer’s wiring diagram and guidelines is essential to ensure a proper and functional installation.

Choosing the Right Wiring Method for Securitron Exit Buttons

Choosing the Right Wiring Method for Securitron Exit Buttons

Securitron exit buttons are an essential part of any access control system, providing a convenient way for users to exit a secured area. When it comes to wiring these exit buttons, there are several options to consider. Each method has its advantages and considerations, so choosing the right wiring method is crucial to ensure the proper functioning of the exit button.

1. Single Gang Box with Conduit: This is the most common method used for wiring Securitron exit buttons. In this method, the exit button is mounted on a single-gang electrical box, and the wiring is run through conduit. This provides a neat and professional-looking installation, while also offering protection to the wiring from physical damage or tampering. It is important to ensure that the conduit is properly sized to accommodate the wiring and that all connections are made securely.

2. Surface Mount Box: In situations where running conduit is not feasible or desired, a surface mount box can be used. This method involves mounting the exit button on a surface mount box, which provides space for wiring connections. The wiring is then run along the surface, either concealed or exposed, depending on the aesthetic requirements. It is important to use appropriate cable management techniques, such as cable clips or raceways, to secure the wiring and prevent any accidental damage.

3. Recessed Mount: For a more discreet installation, a recessed mount can be used. In this method, the exit button is mounted inside a wall, with the wiring concealed behind the wall. This gives a clean and unobtrusive appearance, as the exit button is flush with the wall surface. However, it may require more planning and preparation during installation to ensure that the wall is properly prepared and that the wiring is safely routed behind the wall. It is also important to consider accessibility for maintenance or future modifications.

Before choosing a wiring method for Securitron exit buttons, it is important to carefully assess the specific requirements of the installation. Factors such as the location, aesthetics, accessibility, and security considerations should be taken into account. Consulting with a professional or referring to manufacturer guidelines can help ensure that the chosen wiring method meets all necessary requirements and ensures the functionality and reliability of the exit button in the access control system.

Wiring Diagram for Securitron Exit Button with Simple On/Off Switch

When installing a Securitron exit button with a simple on/off switch, it is important to properly wire the components to ensure proper functionality and security. The wiring diagram provided below illustrates the correct connections for this setup.

Components:

  • Securitron exit button
  • Simple on/off switch
  • Power supply
  • Electric strike or magnetic lock

Wiring guide:

  1. Connect the positive terminal of the power supply to one side of the on/off switch.
  2. Connect the other side of the on/off switch to one terminal of the Securitron exit button.
  3. Connect the other terminal of the exit button to the positive terminal of the electric strike or magnetic lock.
  4. Connect the negative terminal of the power supply to the negative terminal of the electric strike or magnetic lock.

By following this wiring diagram, the on/off switch can be used to control the power supply to the Securitron exit button, which in turn controls the lock or strike. This setup provides a simple and convenient way to control access to a secure area.

Please note:

This wiring diagram assumes that the power supply is already connected to a reliable power source and properly grounded. It is important to follow all local electrical codes and regulations when installing any electrical components.

Step-by-Step Guide: Wiring Securitron Exit Button with Magnetic Lock

When it comes to securing an access control system, wiring an exit button with a magnetic lock is an essential step. This guide will provide you with step-by-step instructions on how to properly wire a Securitron exit button with a magnetic lock.

Materials Needed:

Materials Needed:

  • Securitron exit button
  • Magnetic lock
  • Power supply
  • Wiring cables
  • Wire strippers
  • Screwdrivers
  • Mounting screws
  • Drill (if necessary)

Step 1: Mount the Exit Button and Magnetic Lock

Start by mounting the exit button and magnetic lock in the desired locations. Ensure that the exit button is easily accessible and at an appropriate height for users to reach. The magnetic lock should be installed on the door frame or corresponding structure.

Step 2: Connect the Power Supply

Next, connect the power supply to the exit button and magnetic lock. Use the wiring cables to connect the positive and negative terminals of the power supply to the corresponding terminals on both the exit button and magnetic lock.

Step 3: Wire the Exit Button to the Magnetic Lock

Take the wiring cables and connect one end to the COM (common) terminal of the exit button. Connect the other end of the wiring cable to the “+” (positive) terminal of the magnetic lock. This will ensure that when the exit button is pressed, the magnetic lock will be disengaged.

Step 4: Test and Secure the Wiring

Once the wiring is complete, test the system to ensure that the exit button properly unlocks the magnetic lock. Press the exit button to verify that the magnetic lock disengages. If everything is functioning correctly, secure the wiring with cable ties or by securing it to the wall or structure to prevent any accidental disconnections.

Following these steps will allow you to properly wire a Securitron exit button with a magnetic lock. Taking the time to ensure proper wiring ensures the security and functionality of the access control system. If you are unsure about any step, consult the manufacturer’s instructions or seek the assistance of a professional.

Wiring Diagram for Securitron Exit Button with Request-to-Exit (REX) Sensor

Wiring Diagram for Securitron Exit Button with Request-to-Exit (REX) Sensor

The wiring diagram for a Securitron exit button with a Request-to-Exit (REX) sensor outlines the connections required for proper functionality. This diagram helps installers and technicians understand how the components should be interconnected to ensure the exit button and sensor work together as intended.

The diagram typically includes labels for each component, such as the exit button, REX sensor, power supply, and access control system. It illustrates the specific wiring connections needed between these components, including the use of appropriate conductors, terminal blocks, and connectors. The diagram also highlights any necessary resistor or diode placements to prevent unwanted backfeeding of electricity or protect sensitive components.

For example, the diagram may show that the exit button connects to the REX sensor using a specific set of wires. It may also indicate that the REX sensor requires a separate power supply connection. Additionally, the diagram may specify which terminals on the access control system should be used for integrating the exit button and REX sensor signals, ensuring proper communication between these components.

Components

Components

  • Exit Button: An integral part of an access control system, the exit button allows authorized individuals to exit a secure area. It is typically a wall-mounted device that people can press to trigger the door release mechanism.
  • Request-to-Exit (REX) Sensor: The REX sensor detects proximity or motion and signals the access control system to release the door when someone approaches it from the inside. It helps ensure a safe and convenient egress.
  • Power Supply: The power supply provides the necessary electrical power to the exit button, REX sensor, and other components of the access control system. It may connect to a building’s electrical system or use a separate power source.
  • Access Control System: The access control system is responsible for managing and controlling access to a secure area. It receives input from devices like the exit button and REX sensor, processes the signals, and controls the locking and unlocking of doors accordingly.

Overall, the wiring diagram for a Securitron exit button with a Request-to-Exit (REX) sensor serves as a valuable resource for installers and technicians. It ensures that the wiring connections are correctly established and facilitates a smooth integration of the exit button and sensor with the access control system, enhancing the overall security and functionality of the system.

Common Issues and Troubleshooting Tips for Securitron Exit Button Wiring

Common Issues and Troubleshooting Tips for Securitron Exit Button Wiring

Securitron exit buttons are an essential component of access control systems, allowing users to easily and securely exit a building or room. However, like any electronic device, wiring issues can arise, causing the exit button to malfunction. In this article, we will discuss some common issues related to Securitron exit button wiring and provide troubleshooting tips to help you resolve these problems.

1. Loose or Incorrectly Connected Wires

1. Loose or Incorrectly Connected Wires

One of the most common issues with Securitron exit button wiring is loose or incorrectly connected wires. Check all the connections to ensure that they are securely fastened to their respective terminals. Additionally, make sure that the wires are connected according to the wiring diagram provided by Securitron. Incorrectly connected wires can result in the exit button not functioning properly or not working at all.

2. Faulty Power Supply

2. Faulty Power Supply

If the Securitron exit button is not receiving power, it will not work. One possible cause of this issue is a faulty power supply. Check the power supply unit to ensure that it is functioning correctly. You can use a multimeter to measure voltage output from the power supply. If the voltage reading is significantly lower than the specified voltage, it may indicate a faulty power supply that needs to be replaced.

3. Defective Exit Button

3. Defective Exit Button

In some cases, the Securitron exit button itself may be defective. If you have ruled out any wiring issues and confirmed that the power supply is functioning correctly, it is possible that the exit button itself is faulty. In this situation, you may need to contact Securitron for further assistance or consider replacing the exit button with a new one.

4. Environmental Factors

4. Environmental Factors

Environmental factors can also affect the performance of Securitron exit button wiring. For example, exposure to extreme temperatures or moisture can cause damage to the wiring, leading to malfunctions. It is essential to ensure that the exit button and its wiring are installed in a suitable environment and protected from any potential hazards.

To summarize, proper wiring is crucial for the reliable operation of Securitron exit buttons. By identifying and addressing common wiring issues, such as loose or incorrectly connected wires, faulty power supply, defective exit buttons, and environmental factors, you can troubleshoot and resolve problems effectively.

Q&A:

What are some common issues with Securitron exit button wiring?

Common issues with Securitron exit button wiring include loose or faulty connections, incorrect wiring configurations, and damaged or worn-out wires.

How can I troubleshoot loose or faulty connections in Securitron exit button wiring?

To troubleshoot loose or faulty connections, you can start by checking all the connections and ensuring they are tight and secure. You can also use a multimeter to test for continuity and check if there are any breaks or interruptions in the wiring.

What should I do if I have incorrect wiring configurations in my Securitron exit button?

If you have incorrect wiring configurations, you will need to review the wiring diagram provided by Securitron and make the necessary corrections. Make sure you follow the manufacturer’s instructions carefully to ensure proper functionality.

How can I determine if the wires in my Securitron exit button are damaged or worn-out?

You can determine if the wires are damaged or worn-out by inspecting them visually for any signs of fraying, cuts, or other physical damage. You can also use a multimeter to test for continuity and check if there are any breaks in the wiring.

Video:

Emergency stop button switch wiring diagram